So here’s the deal: I’m staying in Orlando, FL at my parents’ home for a large portion of spring break. I wanted to take some radio equipment, and set up a simple antenna to allow me to operate. This post documents what I did, and only time will tell how well my configuration actually works!
Let’s start with the video. It summarizes the antenna, and even shows me making my 1st contact with it to a guy in Vermont, and I’ve been getting good signal reports from Europe and South America as well.
This is what I started with. It’s pink because it’s the bedroom of my younger sister Leah. It might be a a little embarrassing to operate in such an environment, but my ego is up for the challenge!
The first thing I did was set up a table and run some wire out the window. I chose a window with a tree near by. The wire is not coax, but rather some el-cheapo speaker wire I found. It’s not 50 ohm impedance, but I imagine it will make the tuner happy anyhow.
I tied some random objects to the end of a fishing line and used a fishing pole to cast them up and over the tree branch I wanted. Believe it or not this took a lot of time, effort, broken lines, and frustration. Have someone help you do it, or practice doing it! I now appreciate how in an emergency situation getting something like this up might not be as easy as it seems…
The end of the wire splits in two and connects to two quarter-wavelength legs of a dipole resonant at the 40m wavelength (7mhz frequency), with each orange piece of wire being about 33ft in length.
When the fishing line looped over the branch (tied to the speaker wire) is hoisted up, the branch acts like a pulley and pulls the whole system up. You can see the junction of the wires if you look closely in the image…
The thing isn’t that visible, which is a plus. I don’t want anyone to know I operate! Notice how the orange wires are virtually invisible, even against a blue sky. Slick!
From far away the most noticeable wire is the speaker wire. I wish it weren’t reflective with a white stripe! Oh well, it’s all I’ve got. It’s more dramatic since the setting sun is behind me. Also keep in mind that there is a tree/shrubbery between my nearest neighbor and me, so I don’t think they can even see it from their house.
The final setup from inside. Poor Leah, I hope she doesn’t cry when she sees this! With the blinds closed I’m confident I can operate with confidence any time of the day. I don’t think I’ll push the setup beyond 40W (even though it can do 100W) just to keep things simple and safe. I look forward to operating CW (Morse code) later tonight! I wonder how this would do as a QRSS receiver? Much experimentation is left to perform! I’m happy knowing that in a very short time I set up a functional antenna to talk across the country at virtually no cost. Since I retained the pulley system, I can lower the antenna when it’s not in use, and hoist it up whenever I want. I’ll post a log of my contacts at the end of the week.
UPDATE: I’ve been making contacts on 40m, 20m, 17m, 12m, and 10m. I’m impressed how well I’ve been doing on 10m! Even with a dipole not cut for 10m, and oriented for north-south propagation, I’m getting Europe on this thing. I don’t know if it’s an improved antenna, or less noise being in a residential neighborhood. (Compare this to the University of Florida Gator Amateur Radio Club station located on top of a hospital). Here is a video showing some random 12m/10m contacts…
ANTENNA UPDATE – I ended up stringing a SECOND (much longer) antenna. Although it’s configured somewhat like a dipole, I consider it more of a long wire antenna. It’s ridiculously long (about 100 ft) and high (about 20 ft). The other wire is more like a RF ground, and is about 150ft. Here’s a photo of the new antenna (yellow) and the old antenna (orange). Both of them are functional, and I can switch between them quickly.
Although I intended the longer antenna for the lower bands (40m, 80m, and why not try 160m?), it seems to work surprisingly well on the higher bands too! I just worked Spain (EA5GPQ) on 24.967 MHz (12m), how cool is that? I can’t wait until later tonight when the lower bands open up. This is pretty fun…
March 10, 2011
While operating from a portable station in Orlando, Florida, I’m taking time to relax and investigate (through experimentation) different methods to rapidly deploy wire antennas. The antenna system described in my last post was taken down, half by me, and half by the storms that slammed central Florida last night and this morning! I also visited a store and purchased some flat 300-Ohm antenna wire (usually used between old TVs and TV antennas) that I hope will serve me well (better than speaker wire, probably less than 50-ohm coax). I used a fishing rod / line to string up the antenna, and here are some photos of the build. At the end you can see a video of my first QSO with this new antenna (OP2A in Belgium, over 4,500 miles away).
March 12, 2011
The end of the week is nearing! Tonight my family flies in from Colorado, and I’m holding my fingers crossed for several reasons. First, this is the first time that anyone in my entire family has seen an amateur radio. They understand it’s a big part of my life, but obviously they don’t really know what it is/does. I imagine I’ll give a demonstration later, and I hope that everything functions well (and I can have a few QSOs), and that it doesn’t come across as fickle. I think there’s quite a disconnect in interests between most of my family and me. For example, the things that I find fascinating (the RX/TX circuitry, my home brew designs, antenna theory, and digital exchanges) are not things I think they can understand or appreciate in the way that I do. Therefore I’m limited to common ground – talking to a few random people out there – and I don’t think that’s very impressive.
I did a quick estimate and it looks like I have a little over 200 contacts from this portable station! I haven’t broken it down by state or country, but I’m excited to dive into the logs a little further down the road. I grabbed a few random videos along the way, so I present the following:
Here I cam sending/receiving some very slow CW on 30m. This is actually one of my first CW contacts on 30m, as I usually just play with QRSS on 10.140MHz!
This is just a demonstration part for informational purposes and part just for me to have and look back on in the future. I’m sure in the future I’ll laugh at the way I operate (I already find it funny how my voice goes up an octave when I pick up a hand mike!), but it is what it is. For newcomers to HF, this represents what can be done just using about 50W of power and a wire antenna hung in a tree!
I also tried my hand at QRSS reception with this antenna (almost forgot to post it). I realized the shortcoming(s) of my QRSS VD software when I couldn’t get it to run on my linux box! The netbook ran Ubuntu and used the pulse audio system and QRSS VD used PyAudio for linux audio support (runs fine on windows though) and PyAudio likes ALSA and not pulse! It’s so frustrating – I wish there were a better cross-platform solution than pyAudio. Anyhow, in a humbling moment I ended-up actually using Argo (my “competitor” program) fired up with WINE under linux (burn, lol) to grab QRSS and save captures, then I used the QRSS Stitcher (my software) to assemble a few hours worth while the XYL and I went out to lunch. Frequency is 10.140MHz. Here’s the result!
AJ4VD Portable Logbook
March 6-12, 2011 (Orlando, FL):
39 States (146 QSOs)
AL: KX4AA, AJ4SE, W7BU
CA: WB2VDH, KI6VJY
CT: WA1VTB, WA1EAJ, KB1GOZ, KD1WN
DE: K3LRH, KB3TXP
FL: N9MDM, KA4ROG, KJ4DOZ, WB4CDH, K5EH, WA4DOS, N1VMC
GA: KT4AO, KI4KGK
IL: W9GD, K9SDM, KC9RET, W9WTF, N9DMK, N9WGT, KB9YXL, KC9CMP
IN: KB9QCC, KC9OTC, KR9E
KT: K4UNW, KB1SIC
LA: KE5UPL, KF5FNR
MA: KB1SWZ, K1MKC, KB1KYN, WB2EBA, K9VNR, K1SVC, N1WRK, K1YCQ
MD: ND3D, W3PG, W3QB, AB3DD
MI: K8DXX, AA8R, K8VB, W8JHA, KD8KMY
MO: K0EHT, KD0CVE, WD6AJQ, WA0BSW, AC2FH, AB0LJ
MS: AE5BR, AD5YB
NC: AJ4BL, AG4IP, WA3OXM, KI4NSP
NJ: KC3QD, WB2NKU, WA3JMV, N2BUE, N2RFA, WA2DAX
NY: W2IHY, K2QNU, KD2BS, AC2ET, KC2MK, KC2LED, KB2EKX, N2RXL, AC2AJ, KB2NCI
OH: KA8RIO, N8SIM, KC8DDQ, N8YN, WB8VWO, AC8CY, KD8NQK, W8WIF, N8PPX, KD8CUT, KA8JIM
OK: KF5GTX, K5CG
PA: WE3C, KB3NXT, W1HFD, W2PWD, AP0PB, N3OW, KB3SDD, W3SOX, KB3UPH, KB3DZL, W1YS
SC: NI8A, N1ITM
TX: KU5Q, W5TWA, KD5NPA, N5TRS, K1PEC, KX5C, KF5CSO, KE5YUO, W5TGB, KB1JJX, AE5WT, W5NR, K5BWF, K3NOQ
VA: WA1ASU, W4VES, W4HH, N4QEX, KX4P, NQ4E, K4WY, WS4W
WI: NL7QC /9, KB9OFM
WV: K8UC, WD8CW, KD8DYA
35 Countries (62 QSOs)
ARGENTINA: LP1H, LU4DX, LS1D
ARUBA: P49Y, P43ADA
BRAZIL: PP5KR, ZW5B, PT7CB, ZX5J, PY2WC, PV8RF
CANADA: VE3MLM, VE9PTR, VE3VEU
CANARY ISLANDS: EC8ADW
CAYMAN ISLANDS: ZF1PB
COLOMBIA: HK1X, HK3ARR
COSTA RICA: TI8M, TI5N, TI5N
CURACAO: PJ2T, JP4G
DOMINICAN REPUBLIC: HI3TEJ, KL7JR (HI3 PORT)
GERMANY: DH7LF, DK1YPA
GUATEMALA: TG9ANF, TG7WW
HUNGARY: HG3R, HA5JI
ITALY: IO5O, IZ4AMS, PJ7DX, IZ6BXV, IZ4BBF
MARTINIQUE: FM5CD, FM5WD
NETHERLANDS ANTILLES: PJ2Z, PJ2/W5FKX
PUERTO RICO: KP4BD
SPAIN: EA5GPQ, EA7OU, EA5FD
TRINIDAD AND TOBAGO: 9Z4AM
VENEZUELA: YV5KG, YY7PMG
VIRGIN ISLANDS: KP2CW